#Antares autotune 7 6x software#

Check the settings.ДЄLARM 52, Auto Tune low Inom: The motor current is too low. H-36 Trip Speed Low (except when starting or stopping) the drive will trip.ДЄLARM 50, Auto Tune calibration failed: Contact the local GE supplier.ДЄLARM 51, Auto Tune check Unom and Inom: The setting of motor voltage, motor current, and motor power is presumably wrong. When the speed is below the specified limit in par. F-17 Motor Speed High Limit the drive will show a warning. The power supply is measured on the control card.ДЄLARM 49, Speed Limit: When the speed is not within the specified range in par. WARNING 48, 1.8 V supply low: The 1.8 Volt DC supply used on the control card is outside of allowable limits. WARNING 47, 24 V supply low: The external 24 V DC backup power supply may be overloaded, otherwise contact the local GE supplier. When powered with three phase mains voltage, all three supplied are monitored. When powered with 24 VDC with the OPC24VPS 24 V DC External Supply Module option, only the 24 V and 5 V supplies are monitored.

There are three power supplies generated by the switch mode power supply (SMPS) on the power card: 24 V, 5V, +/- 18V. E-57 Term X30/7 Digi Out (OPCGPIO) (OPCGPIO General Purpose I/O Option Module).ДЄLARM 46, Power card supply The supply on the power card is out of range. For X30/7, check the load connected to X30/7 or remove the short-circuit connection. E-56 Term X30/6 Digi Out (OPCGPIO)(OPCGPIO General Purpose I/O Option Module). WARNING 42, Overload of Digital Output on X30/6 or Overload of Digital Output on X30/7 For X30/6, check the load connected to X30/6 or remove the short-circuit connection. WARNING 41, Overload of Digital Output Terminal 29 Check the load connected to terminal 29 or remove the short-circuit con- nection. WARNING 40, Overload of Digital Output Terminal 27 Check the load connected to terminal 27 or remove the short-circuit con- nection. The problem could be on the power card, on the gate drive card, or the ribbon cable between the power card and gate drive card. The signal from the IGBT thermal sensor is not available on the power card. Option in slot C1: Hardware incompatible with Control board hardwareДЄLARM 39, Heatsink sensor No feedback from the heatsink temperature sensor. Option in slot C0: Hardware incompatible with Control board hardware Option in slot B: Hardware incompatible with Control board hardware Option in slot A: Hardware incompatible with Control board hardware No communication from ATACD to DSP (state running)ДЈ072-5122 Parameter value is outside its limits Power size information between the power cards does not match Too many power card locations have been registered as present Power card configuration is determined to be incorrect after the delay for power cards to register Power card configuration is determined to be incorrect at power upДЄ power card has stopped communicating while main power is applied Debugging of power part data Motor Orientated Control data not transferred correctlyДў064-2072 H081x: option in slot x has restarted 2080-2088 H082x: option in slot x has issued a powerup-wait 2096-2104 H083x: option in slot x has issued a legal powerup-waitД¬ould not read any data from power EEPROM Debug information written in KeypadДSP watchdog is active. Option C1 did not respond when calculating Platform Version.ДЄn exception in the Application Orientated Control is reg- istered. Option C0 did not respond when calculating Platform Version.

Option B did not respond when calculating Platform Ver- sion. Option A did not respond when calculating Platform Ver- sion. Option SW in slot C1 is not supported (not allowed) Option SW in slot C0 is not supported (not allowed) Option SW in slot B is not supported (not allowed) Option SW in slot A is not supported (not allowed)

#Antares autotune 7 6x software#

Parameter value outside of min/max limitsДЎ024-1279 A can message that has to be sent, couldn't be sentД¬annot read Digital Signal Processor software version Missing or invalid Barcode data in EEPROM Serious hardware failureД¬ontrol board EEPROM data is defect or too oldД¬ommunication time out reading EEPROM dataДЄpplication Orientated Control cannot recognize the EE- PROM dataД¬annot write to the EEPROM because a write command is on progress ALARM 38, Internal fault: Contact the local GE supplier.